manualshive.com logo in svg

Fujitsu 10 ppm, User Manual, Page: 58 / 146

Share
Download
Fujitsu 10 ppm User Manual Download Page 58

User’s Manual

3-13

PRINTING AND
PAPER HANDLING

Menu Functions

Use 

+

 and 

-

 to move up and down the options list.

When an item is displayed, 

ENTER

 selects that option (adds an

asterisk after the option indicating that the option is stored in RAM).

MENU

MENU

MENU

SETUP MENU

QUALITY MENU

PAPER

                    LETTER*

MENU

PAPER

                      LEGAL

+

–

+

SMOOTHING

                             ON*

SETUP MENU

PAGE FORMAT MENU

COPIES

                              001*

ENTER

COPIES

                              002

+

–

+

–

MENU

READY

ENTER

–

+

–

MENU

SMOOTHING

                            OFF

Submenus, Items, and Options

The following table shows all of submenus and items and summary
of options displayed on the message display in menu mode. The
display initially shows the factory default option followed by an
asterisk (underlined in the table).

Summary of Contents for 10 ppm



















































































































































Reviews:

No comments