Fuji Xerox ApeosPort-V 4070 Administrator'S Manual Download Page 695 | Manualshive

Page: 695 / 719

background image

Notes and Restrictions

693

A

p

pe
ndi
x

16

Notes and Restrictions for Using Bonjour

This section describes notes and restrictions to observe when using Bonjour.

Supported Environment for Bonjour

Bonjour is available on Printer Setup Tool (Print Center, Printer Setup Utility) of Mac OS X
10.5/10.6, Mac OS X 10.7 Lion, OS X 10.8 Mountain Lion, OS X 10.9 Mavericks, or Macintosh
computers that use Safari. The Discovery feature of Bonjour is available only within the
same subnet.

Printer Name

z

If you change a printer name or a host name that is already assigned, documents may be
printed by a printer that is not selected.

z

If a printer name or a host name is duplicated on the same network, one of the duplicated
names is automatically changed by adding a number to avoid duplication.

z

If you change a printer name or a host name, because of the limitation on the number or
type of characters used, a name differing from the designated name may be assigned.
We recommend that you not change printer names or host names.

Notes and Restrictions for IPv6 Connection

This section describes notes and restrictions to observe when using IPv6 connection.

z

Printing via IPv6 supports the following versions of the operating systems.

- Windows  Vista
- Windows  7
- Windows  8
- Windows  8.1
- Windows Server 2008
- Windows Server 2008 R2
- Windows Server 2012
- Windows Server 2012 R2
- Linux distribution that Common Unix Printing System supports IPv6 and is printable

z

IPv6 does not support the following protocols:

- UPnP Discovery

z

Some features of SMB are not supported (If you attempt to use services with a NetBIOS
name, communication may not be available in some environment).

z

IPv6-in-IPv4-tunneling in the machine itself is not supported.

Important •

If [IP Mode] is set to [IPv6 Mode], the IPv6-inIPv4-tunneling cannot be performed.

z

If more than one router exist in the same subnet, a communication error may occur.

z

In a dual stack environment, some services may cause performance problems depending
on the network settings (for example, when you attempt to set the machine to prioritize
IPv6 in an environment where the Web server is started with IPv4).

z

In a multi-prefix environment (where multiple IPv6 global addresses are used), data
transmission from the machine to a device installed on another network may fail.

z

In a multi-prefix environment (where multiple IPv6 global addresses are used), an address
that is not assigned to the machine may be used for communication.

«
...
693
694
695
696
697
...
»

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Brand: Partner Pages: 81

Brand: Star Pages: 82

Brand: Xerox Pages: 2

Brand: Mitsubishi Pages: 86

Brand: Xerox Pages: 70

Brand: Citizen Pages: 46

7760DX - Phaser Color Laser Printer

Brand: Xerox Pages: 4

THERMOMARK CARD

Brand: Phoenix Contact Pages: 35

Brand: Oki Pages: 138

THERMOMARK ROLLMASTER 300

Brand: Phoenix Contact Pages: 42

Brand: IBM Pages: 16

Brand: Olivetti Pages: 558

Brand: Kyocera Pages: 72

Brand: Digital Equipment Pages: 122

Brand: Oki Pages: 175

Brand: Oki Pages: 110

WorkCentre WC7530

Brand: Xerox Pages: 280

imagePRESS V1000

Brand: Canon Pages: 123

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands