manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

Notes and Restrictions

691

A

p

pe
ndi
x

16

z

When setting the network such as IP addresses with a host used under the Network 
Information Service (NIS), consult your NIS administrator.

„

SMB Authentication

When an IP address or a host name is used to designate the authentication server for SMB 
authentication, even if the domain name is incorrect, the authentication succeeds if the 
correct user name and passcode are entered.

Notes and Restrictions for Using TCP/IP

This section describes notes and restrictions to observe when using TCP/IP (LPD).

„

Configuration on the Machine

z

IP addresses are managed for the entire system. Configure the settings only after 
consulting your network administrator.

z

The setting of subnet mask and gateway addresses may be required depending on the 
network environment. Consult your network administrator and configure the required 
settings.

z

When the port status is set to [Enabled], it may automatically switch to [Disabled] if the 
machine has insufficient memory. In this case, either set an unused port to [Disabled] or 
adjust the assigned memory size.

z

Adjust the receiving buffer size for LPD in [Receiving Buffer - LPD] according to usage. If 
the receiving buffer size is smaller than the transmitted data, the machine may not be 
able to receive the data.

„

Configuration on the Computer

z

IP addresses are managed for the entire system. Configure the settings only after 
consulting your network administrator.

z

When setting the network such as IP addresses with a host used under the Network 
Information Service (NIS), consult your NIS administrator.

„

Turning Off the Machine

Check the following points when turning off the machine:

z

When [Receiving Buffer - LPD] is set to [Spool to Memory]

All print data spooled within the machine memory, including the data which is being 
printed, is erased. The print data does not remain when the machine is turned on again.

However, if the machine was turned off immediately after a computer instructed a print 
job, the job may remain on the computer. In this case, when the machine is turned on, the 
data stored on the computer is printed before any jobs instructed subsequently.

z

When [Receiving Buffer - LPD] is set to [Spool to Hard Disk]

All print data spooled in the machine hard disk, including the data which is being printed, 
is saved. In this case, when the machine is turned on, the data stored on the machine hard 
disk is printed before any jobs instructed subsequently.

z

When [Receiving Buffer - LPD] is set to [No Spooling]

All print data spooled in the machine receiving buffer, including the data which is being 
printed, is erased. The print data does not remain when the machine is turned on again.

However, if the machine was turned off immediately after a computer instructed a print 
job, the job may remain on the computer. In this case, when the machine is turned on, the 
data stored on the computer is printed before any jobs instructed subsequently.

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Oki C910 Service Manual preview
C910
Brand: Oki Pages: 282
Pantum M9106 Series User Manual preview
M9106 Series
Brand: Pantum Pages: 164
Durst Rho 600 Pictor Specifications preview
Rho 600 Pictor
Brand: Durst Pages: 2
Citizen CMP-10 Command Reference Manual preview
CMP-10
Brand: Citizen Pages: 80
Fuji Xerox apeosport-v c5585 User Manual preview
apeosport-v c5585
Brand: Fuji Xerox Pages: 493
Intermec 681T Specifications preview
681T
Brand: Intermec Pages: 2
Ricoh fax5600 Operator'S Manual preview
fax5600
Brand: Ricoh Pages: 269
Ricoh Aficio AP400 Quick Installation Manual preview
Aficio AP400
Brand: Ricoh Pages: 2
Xerox 490 DC/ST User Manual preview
490 DC/ST
Brand: Xerox Pages: 85
Magicard Pronto 100 User Manual preview
Pronto 100
Brand: Magicard Pages: 42
Lanier AP3200 Operator'S Manual preview
AP3200
Brand: Lanier Pages: 140
Xerox DocuPrint 4635 IPS Series Code List preview
DocuPrint 4635 IPS Series
Brand: Xerox Pages: 16
Tachosys digiprint Instruction Manual preview
digiprint
Brand: Tachosys Pages: 5
Canon varioPRINT 6000 TITAN Series Manual preview
varioPRINT 6000 TITAN Series
Brand: Canon Pages: 69
Canon WS8400 Service Manual preview
WS8400
Brand: Canon Pages: 224
Canon Your MX892 Setting Up preview
Your MX892
Brand: Canon Pages: 29
Canon imageCLASS LBP913w User Manual preview
imageCLASS LBP913w
Brand: Canon Pages: 327
Canon imageRUNNER ADVANCE C255i Getting Started preview
imageRUNNER ADVANCE C255i
Brand: Canon Pages: 16

Brands by name

Popular brands

Load more brands