manualshive.com logo in svg

Fluidwell D030-P Series, User Manual, Page: 41 / 44

Share
Download
Fluidwell D030-P Series User Manual Download Page 41

FW-D030-P-MAN-EN-V0102_02

35

B

APPENDIX

Troubleshooting the D030-P

In this appendix several issues are described that may occur during installation or operation of 
your D030-P.
If you have an issue that is not reported here, please contact your supplier.

Response not as expected

Flowmeter does not generate pulses

Check:
• Signal selection - See 

 51  "Signal" on page 25,

• Pulse amplitude - See “I/O wiring options” on page 13.
• Flowmeter, wiring and connection of terminal connectors - See “Electrical installation –

general” on page 9.,

• Power supply of flowmeter - See “Power Supply Wiring” on page 10..

Flowmeter generates "too many pulses"

Check:
• Settings for Total - See 

 11-15,

• Type of signal selected with actual signal generated - See 

 51  "Signal" on page 25,

• Sensitivity of coil input - See 

 51  "Signal" on page 25 and "Sine-wave (Coil) Signal" on 

page 13.

• Proper grounding of the F030-P - See “Electrical installation – general” on page 9.
• Use screened wire for flowmeter signals and connect screen to terminal 9. (unless connected

at sensor)

No access (unknown password)

If the password is unknown and it is not 

1234 (default password)

, there is only one possibility 

left: call your supplier.

Alarm

When 

 starts to blink a system alarm has occurred. 

System alarms

To view system alarms press the 

START/

 button several times. This displays the 5-digit error 

code.

Possible codes are:

Note:

Only one code is displayed. When more alarms are active simultaneously the alarm 

codes are added.

0001

irrecoverable display-data error: data on the display might be 
corrupted.

0002

irrecoverable data-storage error: the programming cycle might have 
gone wrong: check programmed values.

0003

error 1 and error 2 occurred simultaneously

SETUP

SETUP

SETUP

SETUP

ALARM

Summary of Contents for D030-P Series













































Reviews:

No comments