background image

User manual D030-P Batch Controller

5 –

 

O

PERATING

 

THE

 D030-P

28

FW-D030-P-MAN-EN-V0102_02

Operator functions

For the operator the following functions are available:

To enter a batch quantity

To change the PRESET-value, following procedure must be followed: 
1 Press PROG: the word "PROGRAM" will be flashing,
2 Use 

 to select the digits and 

 to increase that value,

3 Set the new PRESET-value by pressing ENTER.

Figure 24: 

Example display information during programming preset value.

When data is altered but 

ENTER

 has not been pressed yet, then the alteration can still be cancelled 

by waiting for 20 seconds or by pressing 

ENTER

 during three seconds: the former value will be 

reinstated. The PRESET-value can be used time after time till a new value is programmed.

Batch maximum

When you program a new value which is not valid - the batch size is too large - the decrease-
sign

 will be displayed while you are programming; the new value will not be accepted! 

Starting up the batch process

The batch process can only be started up when "READY" is displayed. The batch process is 
started-up by pressing the START-key. 
The arrows at the display indicate if the ACTUAL-value is / was counting up or down.

Figure 25: 

Example display information during the process.

Press 

STOP

 to "PAUSE" the batch process. Pressing this key twice finishes the process completely and it 

can't be continued. 

STOP

 is also used to select Total and accumulated total and to select a value (In Program 

mode).
Use this key when you see 

STOP

 or   in the text.

Note:

Please note that alterations will only be set after 

ENTER

 has been pressed!

RUN

PAUSE

LOW BATTE RY

SET-UP

ALARM

PROGRAM

READY

RUN

PAUSE

SET-UP

ALARM

PROGRAM

READY

Summary of Contents for D030-P Series













































Reviews: