Fischer Panda AGT 6000 PVMV-N Manual Download Page 96

Page: 96 / 132

Appendix

Page 94 AGT 6000 PVMV-N 12V_24V - Chapter E: Appendix

E.3

Troubleshooting

GENERATOR OUTPUT VOLTAGE TOO LOW

If the generator delivers less than 80V current ("undervoltage"), there can be various reasons for this:

Cause

Solution

Generator is overloaded.

Reduce the electrical load. (Switch off consumers)

Motor is not reaching the rated rpm.

Refer to "motor faults" section.

Actuator is not in maximum position.

Check actuator resp. renew.

VCS-voltage controler defective or wrong adjusted.

Check resp. renew.

GENERATOR VOLTAGE TOO HIGH (MORE THAN 80V)

The following reasons may be the cause, if the generator delivers more than 80V ("overvoltage"):

Cause

Solution

The engine is running at the wrong speed.

Check the speed of the motor with a rev or frequency
counter, set the correct speed.

VCS-voltage controler defective or wrong adjusted.

Check resp. renew.

Actuator defective.

Check resp. renew.

GENERATOR VOLTAGE FLUCTUATES

Cause

Solution

1. Fault or defect on the consumer side.

2. A motor fault.

1. Check if the power requirement of the consumer
fluctuates.

2. See "Motor running irregularly".

MOTOR DOES NOT TURN OVER WHEN STARTING

Cause

Solution

Battery main switch is switched off.

Check the position of the battery main switch, if neces-
sary switch on..

Battery voltage not sufficient.

Check that connection is firm and whether corrosion
has occurred..

Starting current fault.

The voltage of full batteries fall to a maximum of 11V.
The wiring is severed if the voltage does not drop. The
battery is discharged if the voltage drops further.

Summary of Contents for AGT 6000 PVMV-N





































































































































Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands

Fischer Panda AGT 6000 PVMV-N, Manual

Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands