Fischer Panda AGT 6000 PVMV-N Manual Download Page 105

Page: 105 / 132

VCS-AGT-U/I

VCS-AGT-UI_eng.fm

Chapter A: VCS-AGT-U/I - Page 103

Fischer Panda Datasheet

A.2.2 Safety instructions for the voltage control

-A broken Cable in the mesurement line will be notice by the VCS and the generator will slow down and stop.

-A short circiut in the mesurement line or a wrong pol connection is not noticed by the VCS (its like that there is

no voltage). The voltage control in this vase ist out of funktion. It is necessary at the installation to check the right
working of the VCS and a second overvoltage protection must be installed.

-For the mesurement voltage a shieldet cable is needet, it must be less than 3 mtr long. The shield should be

connected to ground at one side.

Note the safety instruction in the generator manual

Please Note

• Run the generator with closed sound cover only

• Recommend: install a smoke connection.

• Ask for regular service

Summary of Contents for AGT 6000 PVMV-N





































































































































Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands

Fischer Panda AGT 6000 PVMV-N, Manual

Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands