Fischer Panda AGT 6000 PVMV-N Manual Download

Page: 129 / 132

Remote Control Panda 6-50

F1WT1-95E730 Panda 6-50 Fernbedienpanel_eng.fm

Kapitel/ChapterA: Remote Control Panda 6-50 - Seite/Page 127

Fischer Panda Datasheet

A.3.11 Requirement for Automatic Start

If there is an automatic starting requirement and if the remote control panel is switched off, this automatic starting
requirement will be ignored. Automatic starting is only possible, after the remote control panel had been switched
on.

A.4 Slave Panel - optional

The Slave Panel has the same buttons and function as the main panel.

To connect the slave panel with the main panel use the small adapter board delivered together with the slave
panel.

For more details see slave panel datasheet.

Fig. A.4-1: Slave panel

A.5 Slave panel and automatik start togther - optional

To use the automatik start option together with the Slave Panel option, you must use the Combo adapter board
Fischer Panda Art. Nr. 21.02.02.01H.

It is the combinied adapter board of both options.

Fig. A.5-1: Slave panel and automatic start

Summary of Contents for AGT 6000 PVMV-N





































































































































Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands

Fischer Panda AGT 6000 PVMV-N, Manual

Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands