Fischer Panda AGT 6000 PVMV-N Manual Download

Page: 81 / 132

Generator Failure

AGT 6000 PVMV-N 12V_24V - Chapter D: Generator Failure Page 79

D.1.3 Adjustment of the maximum upper revolution

1. Disconnect the plug at the electrical supply line of the actuator.

2. Unclamp the countering nut at the limitation screw with a wrench SW 10.

3. Connect an electrical voltage instrument (voltmeter) with a display range until 100V DC to the

clamps 7 and 8 of the VCS.

4. Be sure that no electrical load is adjusted.

5. Start the generator.

6. Increase the rev of the generator by turning the spindle of the actuator manually until the volt-

meter reach a value of 33V DC.

7. Turn the limit stop screw tight against the limit stop point at the rev regulator lever.

8. Protect the limit stop screw with the countering nut.

9. Check again if the voltage of the generator is limited to max. 33V without load.

The adjustment of the upper limitation of the rev serves an additional safety. The value of the
max. voltage lies 5V above the normal operating border.

01. Countering nut

02. Adjusting screw for upper limitation

03. Speed regulator lever

This adjustment should not be chan-
ged, otherwise the warranty expires.

Fig. D.1.3-1: revolution

Summary of Contents for AGT 6000 PVMV-N





































































































































Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands

Fischer Panda AGT 6000 PVMV-N, Manual

Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands