Fischer Panda AGT 6000 PVMV-N Manual Download

Page: 82 / 132

Generator Failure

Page 80 AGT 6000 PVMV-N 12V_24V - Chapter D: Generator Failure

D.1.4 Adjustment of the normal rev limitation

Adjusting the lower limitation:

1. Disconnect the plug at the electrical supply line of the actuator.

2. Unclamp the countering nuts with two wrench SW 10.

3. Connect an electrical voltage instrument (voltmeter) with a display range until 100V DC to the

clamps 7 and 8 of the VCS.

4. Be sure that no electrical load is adjusted.

5. Start the generator.

6. Decrease the rev of the generator by turning the spindle of the actuator manually until the volt-

meter reach a value of 23V DC.

7. Both nuts must be screwed tight.

8. Check again if the lower voltage of the generator is limited to min. 23V without load.

Adjusting the upper limitation:

1. Proceed like before and tighten the countering nuts at a voltage of max. 33V without load.

2. Check again if the upper voltage of the generator is limited to this value.

01. Adjusting nut for upper rev limitation

02. Adjusting nut for bottom rev limitation

Fig. D.1.4-1: Normal rev setup

If the adjustment is finished the plug of the actuator must be re-connect for operation.

Summary of Contents for AGT 6000 PVMV-N





































































































































Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands

Fischer Panda AGT 6000 PVMV-N, Manual

Search results

Summary of Contents for AGT 6000 PVMV-N

Reviews:

Related manuals for AGT 6000 PVMV-N

Brands by name

Popular brands