FARMSCAN Jackal Manual Download Page 31 | Manualshive

Page: 31 / 52

FARMSCAN Jackal Manual Download Page 31

AM-JACKAL-35 / JULY 2020

29

CALIBRATION (MANUAL SET)

Manual set allows for the manual input of a known pulse per litre (PPL) factor. The pulse per litre factor can be
obtained from the flow meter manufacture or from the plastic tag attached to the flowmeter.

Highlight 1.000000 under

MANUAL RATIO

& press

EDIT

Using the NAV buttons enter

the PPL factor as displayed on

the flow meter tag.

i.e. 91.2

Press

EXIT

when done.

Press

NEXT

to accept the new

manual ratio (PPL)

Using the NAV buttons

select how you would like

the UOD to be displayed on

the front screen.

Press

NEXT

You have the option to set

Alarm Min/Max points if

required. Using the NAV
buttons select &

EDIT

as

required. Press

NEXT

Name the input if you desire,

Press

EDIT

or Press

NEXT

The Wizard is now complete.

Press

NEXT

You will be returned to the

Front Screen.

THIS ENDS THE MANUAL CALIBRATION WIZARD SETUP FOR FLOW METER

** IT IS ADVISED TO CHECK YOUR MANUAL CALIBRATION BY MEASURING OUT A KNOWN QTY TO CONFIRM PPL**

THIS CAN BE DONE BY COMPLETING THE CALIBRATION AUTO SET ON THE PREVIOUS PAGE (28)

«
...
29
30
31
32
33
...
»

Summary of Contents for Jackal





















































Reviews:

No comments