FARMSCAN Jackal Manual Download Page 29 | Manualshive

Page: 29 / 52

FARMSCAN Jackal Manual Download Page 29

AM-JACKAL-35 / JULY 2020

27

FLOW METER SETUP (WIZARD)

The Jackal can be configured to monitor liquid products. If only one input is used the Jackal
main screen will display the flow information of your choice. If the Jackal is also setup and
installed with a Wheel Sensor input, the Jackal can be setup to display L/Ha for example.

NB: AT NO STAGE CAN THE JACKAL MONITOR TAKE INTO ACCOUNT MULTIPLE
SPRAY SECTIONS TURNING ON/OFF. TALK TO US ABOUT THE JACKAL CONTROL SERIES.

Sensors Required

•

3 Wire Flow Sensor (Square Wave)

Available Connections:

Refer to Installing Sensors from

PAGES 9-11

The example uses Input 2 – Polmac Flow Sensor

SETUP

From the front screen press

SETUP

Highlight

WIZARD

and press

SELECT

Highlight

FLOWMETER

and

press

NEXT

Highlight and select the

appropriate sensor

INPUT

as

described above and press

NEXT

Choose your

calibration method

Edit the unit of Pulse or leave

as is.

Auto Set > PAGE 28

Manual Ratio > PAGE 29

«
...
27
28
29
30
31
...
»

Summary of Contents for Jackal





















































Reviews:

No comments