manualshive.com logo in svg

FARMSCAN Jackal, Manual, Page: 14 / 52

Share
Download
FARMSCAN Jackal Manual Download Page 14

 

 

 

AM-JACKAL-35/ JULY 2020 

12 

REMOTE RUN/HOLD (ACTIVATE BY OUTPUT) 

 

The Jackal Monitor has the ability to Run/Hold an external 
device such as a remote clutch switch. 

There are 6 outputs available on the Jackal. 

(A8-A9 & B6-B9)

 

This allows you to press the Run/Hold on the Jackal to enable an 
external operation. 

NB: This function is used in conjunction through an automotive 
relay. 

Example: Hella Automotive Relay (12v / 30A) – 4RA003510-08 

 

 

Pin 86

 to 

A9 Out 1

 (12v Run/Hold Output) 

Pin 85

 to 

A7 

(Ground) 

Pin 30

 to 

12v in

 (Direct to Vehicle Battery) 

Pin 87

 to 

Positive Side

 of clutch switch 

(Ensure negative/ground on other side of switch returns to battery)

 

Enable the remote run/hold out by: 

 

 

 

 

From the front screen press 

SETUP

 

Highlight 

OUTPUTS

 and press 

SELECT

 

Highlight 

1: NONE

 and press 

SELECT

 

Press 

EDIT

 and change to 

MODE: Run/Hold 

Press 

EXIT 

Run/Hold can be changed 

from +12V/0V to 0V/+12V 

by pressing 

EDIT 

 

 

 

 

Press 

EXIT 

when done.

 

 

 

 

 

 

Summary of Contents for Jackal





















































Reviews:

No comments