FARMSCAN Jackal Manual Download Page 17 | Manualshive

Page: 17 / 52

FARMSCAN Jackal Manual Download Page 17

AM-JACKAL-35 / JULY 2020

15

MAIN MENU

The level of Jackal unlock will determine what options are viewable and available to be edited.

Use the NAV button down to reveal further menu information

Wizard

Run a predefined wizard for setting up the Jackal Monitor as:

•

Sprayer (Automatic Mode) –

Control Version

•

Area/Speed Wheel

•

Area/Speed GPS

•

Tachometer (Fast & Slow option available)

•

Flow Meter

•

Slippage Meter

•

Generic Wizard

Inputs

Manually enable or edit ports in which sensors are connected to.

Front Screen

Enable/define/order/edit/name the lines on the front screen.
Select the number of decimal places displayed and edit the alarms.

Other

Change speed input, implement & section widths, external run/hold

Settings

alarm notification

s

ettings (beep & on hold), language options, speed simulation for

diagnostics.

Outputs

This menu is used to control the Jackal outputs. Refer to this manual and edit the outputs
described ONLY to prevent damage to external sensors connected to the Jackal.

GPS/Serial

When an external GPS is connected view and ensure the GPS is setup correctly.
Setup baud rate and confirm GPS messages (NMEA messages RMC or GGA+VTG are
required) Latitude, Longitude, heading, speed, date & time.

About Jackal

Shows current version of Jackal software and unlock codes installed on the unit.

Diagnostics

Shows current input voltage and input diagnostics on enabled ports.

Factory Reset

Returns the Jackal to factory default.

«
...
15
16
17
18
19
...
»

Summary of Contents for Jackal





















































Reviews:

No comments