FARMSCAN 74V1 Operator'S Manual Download Page 65 | Manualshive

Page: 65 / 103

FARMSCAN 74V1 Operator'S Manual Download Page 65

February 2017

www.farmscanag.com

AM-74V1-4

64

Jobs (2)

CREATING A JOB – WITH A COVERAGE MAP

The 7000 has the ability to draw & record a live coverage map of worked area when a GPS is connected to
the AC-7000 harness. It is recommended that only one job is active and coverage is recorded at one time.

Farmscan Ag recommends placing the live coverage map on Tab 4 as it displays in a whole screen format.

Refer to PAGE 91 for example view.

Note : At current release 2.17 individual sections turned on/off are not displayed on the coverage map,
however are recorded correctly and adjusted during the export and job details via CSV format.

1.

Navigate to the Job page.

2.

Select the + button.

3.

Enter your preferred Job name.

4.

Ensure that ACTIVE & COVERAGE are both ticked

5.

Select the green Tick button.

The ACTIVE job will be displayed on the Front Tile and accumulate hectares. When changing Active jobs
you will be prompted to Replace the front screen data related to this job (As below)

Simply select the new Job that you wish to display on the Front Screen Tile to record the new job details.

2

3

«
...
63
64
65
66
67
...
»

Summary of Contents for 74V1








































































































Reviews:

No comments