manualshive.com logo in svg

FARMSCAN 74V1, Operator'S Manual, Page: 35 / 103

Share
Download
FARMSCAN 74V1 Operator'S Manual Download Page 35

 

February 2017 

www.farmscanag.com 

AM-74V1-4 

34 

Machine Setup 

Prime Mode operation explanation 

The Prime Mode operation turns on the spray valves; the flow will be regulated as if the implement was 
travelling at the Prime Speed. If the implement exceeds the Prime Speed or the Prime Time then the flow 
will be regulated normally; the Spray Section Control will also revert to Run Mode. 
 

 

1.

 

Enable Prime 

a.

 

If Prime Mode is enabled, activating spray control will enter Prime Mode instead of Run 
Mode. 
 

 

 

2.

 

Prime Time Mode 

a.

 

Set Time: When Prime is enabled and Prime Time set, after X seconds the spray section 
control will revert to Run Mode. 

b.

 

Continuous: The unit will remain in Prime Mode indefinitely. 

NOTE:

 This should NOT be 

used in standard operation but it is useful for “stand still” testing and demonstration. 
 

 

 

3.

 

Prime Time 

a.

 

If Prime Mode is entered, after the selected number of seconds the Spray Section Control 
will revert to Run Mode. 
 

 

 

4.

 

Prime Speed 

a.

 

When in Prime Mode, the flow control is regulated as if the implement was travelling at 
the Prime Speed. 

b.

 

If the implement exceeds the Prime Speed, Spray Section Control will revert to Run Mode. 

 

 

Speed

Control

Rate

Prime

Speed

Revert
to Run

Mode

Rate @

Prime

Speed

Summary of Contents for 74V1








































































































Reviews:

No comments