manualshive.com logo in svg

FARMSCAN 74V1, Operator'S Manual, Page: 10 / 103

Share
Download
FARMSCAN 74V1 Operator'S Manual Download Page 10

 

February 2017 

www.farmscanag.com 

AM-74V1-4 

 

9 

Installation of Terminal – Smart Switch - UniPOD 

CONNECTION TO SMART SWITCH & UNIPOD 

 
Located on the AC-7000 harness is a 4-way (Female) Deutsch style plug, used for CANbus communications 
to the Smart Switch & UniPOD 

 

 

 

 

 

 

Connect the inline “Y” cable from the Smart Switch into the CANBus IN on the harness as shown above. 
The other end will connect to an extension cable down to the UniPOD on the implement. 
 

RUNNING THE CABLES 

 

From the CANbus IN/OUT on the AC-7000 cab harness or Smart Switch “Y”, run the main CANbus Extension 
(AC-2012-XX) to the rear of the tractor and connect into CANbus IN connector on the AC-740X harness 
connected to the UniPOD. 

 
NOTE: 

Extra CANbus extension cables are available to purchase for connection between tractor and 

UniPOD on the implement. 
 

NOTE: 

As a precaution, avoid running the controller harness alongside other electrical cables in the cab.  

Use cable ties to secure cable away from risk of damage.

 

 

 

 

 

Run CANbus cable from Monitor to UniPOD. 

Extensions cables are available for purchase. 

74V1 Monitor 

UniPOD to control bank 

Power 

Input 

To AC-7000 Harness 

Extension down to UniPOD 

Summary of Contents for 74V1








































































































Reviews:

No comments