FARMSCAN 74V1 Operator'S Manual Download Page 12

Page: 12 / 103

February 2017

www.farmscanag.com

AM-74V1-4

Installation of Terminal – Smart Switch - UniPOD

SENSOR CONNECTIONS

To connect sensors:

Connect the sprayer harness supplied to sensors and valves via the UniPOD.

Connect the labelled connectors on the loom to their respective sensors (flow control valve,
pressure sensor, flow meter, section valves, dump valve.

NOTE:

Connect power last after all installation is finished.

NOTE:

UniPOD requires

separate 12v Power input.

Input is protected by a

10AMP Fuse

EXAMPLE

AC-7405 - 5 Section Harness

NOTES:



It is advised to use the
same power source to
power the UniPOD that is
being used to power the
7000 terminal.



Always take power
directly from the battery.

Connect sections as per labels



AC-7721 : Section
Valve Adapter Plugs

Insert AC-7700 Power Relay

OUT: Insert AC-7700 CANbus terminator

if only one UniPOD is installed

Connect sensors as per labels



AC-7722 : Flow Control Adapter Plug

Connect to UniPOD

IN: Extension cable from

Tractor Cab Display

Insert 2 Wire Wheel Speed

Sensor

ONLY 3 WIRE SECTION VALVES CAN BE USED

WITH THE 74V1. 3 TO 2 WIRE VALVE ADAPTERS

ARE AVAILABE FOR PURCHASE

(Farmscan Ag Part # A-2091)

Summary of Contents for 74V1








































































































Search results

Summary of Contents for 74V1

Reviews:

FARMSCAN 74V1, Operator'S Manual, Page: 12 / 103

Search results

Summary of Contents for 74V1

Reviews: