FARMSCAN 74V1 Operator'S Manual Download Page 32

Page: 32 / 103

February 2017

www.farmscanag.com

AM-74V1-4

Machine Setup

MACHINE SETUP

The Machine tab allows setup of the master control features on the 74V1 used for boom spray operation.



Control (1)

Control Speeds

(Minimum, Slow Hold, Prime)

Auxiliary Setup

(Dump, Output)

NOTE:

Will only display when UniPOD is attached.

Pressure Sensor

(Farmscan Ag Part# AA-114 or User Defined/Custom)

Second Line

(Line Mode, Split, Multi)



Measurements (2)

Use Section Control Set up/enable single section width

Set Section Widths

Set up individual section widths



Speed Source (3)

Wheel

Set up/ calibrate or Set to Enabled

GPS

Enable/ view NMEA strings or Set to Primary

External



Tracmap/TUVR

Set up as task controller



Serial Input

Check communications on the COM Port

Radar

Not currently being used



CANbus (4) – Select Down arrow to reveal

Configure UniPOD’s Confirm & configure connection to UniPOD



UniPOD Status

Check supply voltage & status to UniPOD

Switch Box

Confirm connection to Smart Switch Box

Run/Hold Switch

Confirm Run/ Hold remote switch operation



Wireless (5)



Mapping (6)

Summary of Contents for 74V1








































































































Search results

Summary of Contents for 74V1

Reviews:

FARMSCAN 74V1, Operator'S Manual, Page: 32 / 103

Search results

Summary of Contents for 74V1

Reviews: