Fagor CNC 8060 Operating Manual Download Page 56

Page: 56 / 172

Operating manual (MC).

CNC 8060
CNC 8065

WORKING

WITH OPERATIONS OR

CYCLES

Gene

l concep

ts.

·56·

: 1709)

3.1.1

G functions associated with the execution of the cycles.

While executing these canned cycles, the CNC shows the following "G" functions in the
window for active functions.

Function.

Canned cycle.

G281

Center punching.

G282

Drilling.

G283

Deep hole drilling.

G284

Tapping.

G285

Reaming.

G286

Boring.

G287

Rectangular pocket with rounding.

G288

Circular pocket.

G289

Simple rectangular pocket.

G290

Surface milling.

G291

Rectangular boss.

G292

Circular boss.

G293

Point-to-point profile milling.

G294

Free profile milling.

G295

Slot milling.

G296

Pre-emptied circular pocket.

G297

Boring with spindle orientation.

G298

Bore milling.

G299

Thread milling.

Summary of Contents for CNC 8060













































































































































































Search results

Summary of Contents for CNC 8060

Reviews:

Brands by name

Popular brands

Fagor CNC 8060, Operating Manual

Search results

Summary of Contents for CNC 8060

Reviews:

Brands by name

Popular brands