Factory Five Racing Type 65 Coupe Assembly Manual Download Page 84

Page: 84 / 442

www.factoryfive.com

508-291-3443



8.8” Rear axle assembly, Box 11 Solid axle Traction Lok brackets, Rear control arms.



Use caution when working with the rear end assembly, it weights 225 lbs.



Skip to the Independent Rear suspension if not installing a Solid axle.



See the donor parts prep section if the control arm holes have not been drilled out

Position the Traction Lok brackets on the rear end with the bolts provided (the two short bolts go on the
sides).

Axle Bracket Driver's Side

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Search results

Summary of Contents for Type 65 Coupe

Reviews:

Related manuals for Type 65 Coupe

Brands by name

Popular brands

Factory Five Racing Type 65 Coupe, Assembly Manual

Search results

Summary of Contents for Type 65 Coupe

Reviews:

Related manuals for Type 65 Coupe

Brands by name

Popular brands