Factory Five Racing Type 65 Coupe Assembly Manual Download Page 232 | Manualshive

Page: 232 / 442

background image

231

www.factoryfive.com

508-291-3443

Mark the tube where it needs to be cut so that the tube will just touch the attaching location.
Remove the tube from the vehicle.
Cut the tube using a hack saw or if available a cut-off wheel. If necessary clean the end up with tin
snips or a grinder.
Shake and blow the tube out so that no metal pieces are in the tube.
Reattach the tube assembly to the engine and tighten the hose to the radiator.

Lower radiator hose

Connect the lower radiator tube to the engine.
Starting at the radiator, route the lower radiator hose over the top of the steering rack tie rod and under
the steering shaft to the water pump.

Mark the tube where it needs to be cut so that the tube will just touch the attaching location.
Remove the tube/hose assembly from the vehicle.
Cut the tube using a hack saw or if available a cut-off wheel. If necessary clean the end up with tin
snips or a grinder.
Shake and blow the tube out so that no metal pieces are in the tube.
Remount the tube assembly and tighten the hose clamps on the mount locations.
Attach the overflow container to the front “X” using the supplied screws.
Attach the overflow tube and nipple to the overflow tank.
Zip-tie the hose to the corrugated upper radiator hose and run it to the radiator fill adapter.

Fan Wiring



Wire crimp tool

«
...
230
231
232
233
234
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Jackco Pages: 11

Brand: Horn Tools Pages: 6

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: BMW Pages: 189

Akerstroms Tx700

Brand: LXE Pages: 146

Brand: Dometic Pages: 24

F-250 Super Duty 2022

Brand: Ford Pages: 740

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brand: Motoalliance Pages: 4

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: Vauxhall Pages: 4

Brand: Blitz Pages: 4

Brand: Whispbar Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands