Factory Five Racing Type 65 Coupe Assembly Manual Download Page 379 | Manualshive

Page: 379 / 442

background image

378

www.factoryfive.com

508-291-3443

Aluminum Splash guards



⅛

”,

3

/

16

” drill bit, drill, rivet gun, silicone, caulking gun, ¾” socket, ratchet, extension, marker,

clamps



Secondary body fasteners, packaged aluminum, front wheel and tire

Front Wheel

With the nose up, put a wheel and tire on the front and turn the steering so that the rear of the tire is as
close as possible to the frame.
Clamp the front lower half of the splash guard to the 1”x 1” tube and (from underneath) to the front part
of the body.



Use a level to make sure the surface that will be close to the nose is flat.

«
...
377
378
379
380
381
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: GMC Pages: 140

CK 3000 Evolution

Brand: Parrot Pages: 2

Brand: Kargo Master Pages: 6

Brand: Phonocar Pages: 2

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

MagicSpeed MS900

Brand: Waeco Pages: 120

Brand: Connects2 Pages: 8

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brand: Metra Electronics Pages: 8

Brand: TRAMEC Pages: 116

Brand: Buick Pages: 20

Brand: Honda Pages: 219

Brand: Prorack Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands