Factory Five Racing Type 65 Coupe Assembly Manual Download Page 197 | Manualshive

Page: 197 / 442

background image

196

www.factoryfive.com

508-291-3443

Engine Harness



⅜

” socket, regular head screwdriver, slip joint pliers,

3

/

16

” and

⅛

” drill bits, drill, #6 nut driver,

electrical tape, wire cutters.



Mustang engine harness, engine harness assembly



The aluminum is laser cut for the EFI (Electronic Fuel Injection) rubber grommets, the kit comes
with block-off covers if a carbureted engine is used.



If you are running a carbureted engine you do not need this section.



Make sure that the battery is not connected any time you are working with the computer.

The engine harness begins in the passenger foot box. The computer plug is pushed through the oval
shaped hole on the passenger footbox top.
Attach the computer to the underside of the top of the passenger foot box using the plastic bracket from
the Mustang and the screws provided. Alternatively, the computer can be mounted to the inside of the
right footbox or Behind the firewall if the optional heater/defroster is

not

being used.

«
...
195
196
197
198
199
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: Lancia Pages: 191

Brand: Camcar Pages: 6

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Axxess Pages: 8

Brand: CITROËN Pages: 301

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: Cadillac Pages: 20

Brand: TATA Motors Pages: 136

Dynamic Power Management Home - Module

Brand: newmotion Pages: 20

Brand: Lexus Pages: 830

Brand: Smappee Pages: 28

Brand: XTC Pages: 2

Brand: Honda Pages: 219

GRAND CHEROKEE 4xe 2023

Brand: Jeep Pages: 440

Brand: Kia Pages: 4

Brand: Fab Fours Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands