Factory Five Racing Type 65 Coupe Assembly Manual Download Page 438 | Manualshive

Page: 438 / 442

background image

437

www.factoryfive.com

508-291-3443

selection tips at the beginning of this manual) so more of the harness parts must be kept or the computer
will need to be flashed.  In 1999 Ford added to the PATS so that the gauge cluster needs to be present to
start the car.  An alternative to using the donor harness would be to use a chassis harness and a stand
alone engine harness.  FFR has a harness for Mass Air engines (89-93).  Ron Francis has a harness for
96-04 engines.

For a carbureted car, we recommend using an aftermarket chassis harness.

Accelerator Pedal

The accelerator pedals remained unchanged from 1979 to 2004, and they all work with FFR kits.

Pedal Box

Pedal boxes are the same from 1982 to 1993. In 1994 the box switched to a new design. This newer
pedal box needs four tack welds to be drilled out, and a notch to be made in the clutch pedal stop to
allow use in an FFR kit. The notch is required for clearance of the gas pedal.

«
...
436
437
438
439
440
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: Yakima Pages: 11

Brand: Uebler Pages: 18

Brand: Taffio Pages: 8

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: DAVIS Pages: 32

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Axxess Pages: 8

Brand: Xblitz Pages: 30

Brand: Mercedes-Benz Pages: 358

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Prorack Pages: 15

Brand: Acura Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands