Factory Five Racing Type 65 Coupe Assembly Manual Download Page 280 | Manualshive

Page: 280 / 442

background image

279

www.factoryfive.com

508-291-3443

Raise or lower the front of the nose so that the bottom edge of the hood is parallel with the bottom edge
of the body above the exhaust area.
Align the rear of the wheel well of the nose with the front of the body.

Move the nose around so there is a small gap (i.e.

⅛

”) along the backside of the nose against the rear

body clip and along the bottom edge of the nose. Use wood or washers in the gap to keep it consistent.



The hood has been trimmed slightly oversized to allow the panel gaps to be sanded down to fit.

Trim the rear edge of the nose with a sander or saw so that the gap is consistent.

«
...
278
279
280
281
282
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: Davis Instruments Pages: 16

Brand: CAMPARK Pages: 20

Brand: Triumph Pages: 86

1306 RAPID SYSTEM

Brand: Thule Pages: 8

Brand: Brodit Pages: 2

Brand: Ironton Pages: 7

Brand: A-Tach Pages: 2

Brand: EUFAB Pages: 12

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Crossland X 2017

Brand: Vauxhall Pages: 245

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Dodge Caravan 2002

Brand: Chrysler Pages: 2399

Brand: Ednet Pages: 6

Brand: Ford Pages: 4378

Brand: Toyota Pages: 549

Brand: Maserati Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands