Factory Five Racing Type 65 Coupe Assembly Manual Download Page 121

Page: 121 / 442

120

www.factoryfive.com

508-291-3443

Adjust the rod ends the same number for turns for the front and rear rod ends on the lower control arm
and upper control arm as required so that



If the number of turns done is the same for all control arms on one side of the suspension, an
alignment is not needed after the installation.

Jack the rear of the car up again and place on jack stands located on the lower control arms near the
shock.
Double check the axle width measurement.

Optional IRS Brakes



¾” wrench, ¾” socket, ratchet, ¾”,

” Hex key, flat head screwdriver, Torque Wrench, Thread

locker.



Bolts used on the caliper that do not use a locknut should have Loctite or other thread locker
applied before installing.

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Search results

Summary of Contents for Type 65 Coupe

Reviews:

Related manuals for Type 65 Coupe

Brands by name

Popular brands

Factory Five Racing Type 65 Coupe, Assembly Manual

Search results

Summary of Contents for Type 65 Coupe

Reviews:

Related manuals for Type 65 Coupe

Brands by name

Popular brands