Factory Five Racing Type 65 Coupe Assembly Manual Download Page 18 | Manualshive

Page: 18 / 442

background image

17

www.factoryfive.com

508-291-3443

Engine/Exhaust parts:

Kit comes with alternate drive pulley assembly, oil filter relocate kit, and

exhaust assembly to adapt Mustang engine and headers to vintage side exit exhausts.

Gauges and Dash and Electrical Assembly:

Kit parts are included to adapt the Mustang wiring

harness. The kit comes with components to build your car with an authentic original street style dash.
Complete assembly comes with aluminum dash, toggle switches and indicator lights, gauges and horn
button.

Interior Accessories:

Authentic style Coupe bucket seats, black vinyl w/fasteners, 5-point Simpson

Brand harnesses, Emergency brake boot, High-quality fabric headliner, Interior rear view mirror
w/fasteners, Stainless steel shifter handle, shift knob, boot, polished ring and fasteners.

Exterior Accessories and Lighting:

DOT approved windscreen, License plate light and bracket,

Ceramic Factory Five nose and tail badges, turn signals, and tail-lights, DOT approved headlights, side
mesh, DOT approved glass rear hatch.

Assembly Manual:

Bound assembly manual that is full of pictures and diagrams.

Fasteners:

Over 1500 top quality zinc plated, chrome and stainless steel fasteners, numbered and

packed individually by assembly.

What You Need

For a complete check off list see the Appendix.

Major Components

Engine:

Small block Ford 289/302/351 engine.

Transmission:

T5, Tremec TKO or T-56 (See the Transmission prep section for more info)

Driveshaft:

1987-1993 Ford Mustang.

«
...
16
17
18
19
20
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: Camcar Pages: 6

Brand: J-Top Pages: 2

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: Triumph Pages: 86

Brand: Carefree Pages: 12

Brand: Alpine Pages: 8

Brand: Tessera4x4 Pages: 20

Brand: Alfa Romeo Pages: 8

Brand: Ecco Pages: 9

Brand: ULTIMATE SPEED Pages: 50

Brand: Brodit Pages: 2

Brand: Warn Pages: 5

Brand: RAM Pages: 13

Brand: Motoalliance Pages: 5

Brand: AIS Pages: 2

Brand: Prorack Pages: 15

Brand: Phonocar Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands