Factory Five Racing Type 65 Coupe Assembly Manual Download Page 68 | Manualshive

Page: 68 / 442

background image

67

www.factoryfive.com

508-291-3443

Donor Spindles



13

/

16

” socket, Torque wrench, Needle Nose Pliers, Rubber Mallet



IFS components, Mustang Spindles.

Make sure the grease boot is in place on the lower ball joint then mount the spindle to the lower control
arm.
Attach the castle nut and torque the ball joint to

106-149Nm (80-110 lbft)

and install a new cotter pin

from the IFS components assembly.

FFR Spindles



13

/

16

” socket, Torque wrench, Needle Nose Pliers, Rubber Mallet



Spindle Assembly, IFS components.

Unpack and lay out the hardware for the spindles assembly.



The spindles are marked DSS (Driver Side Spindle) and PSS (Passenger Side Spindle). These
refer to the way they are mounted on the FFR Hot Rod. Which is rear steer The FFR Roadster
uses these as Front steer so they are mounted opposite, The DSS spindle is mounted on the
Passenger side and the PSS spindle is mounted on the Driver side.

Make sure the grease boot is in place on the balljoint then mount the spindle to the lower control arm.

«
...
66
67
68
69
70
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: Ranger design Pages: 6

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Velleman Pages: 6

01 29 9 416 497

Brand: BMW Pages: 5

Brand: Toyota Pages: 52

Ride-Rite Air Helper Springs 2173

Brand: Firestone Pages: 4

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: Vauxhall Pages: 95

Brand: Mitsubishi Pages: 367

Brand: MMD Pages: 3

Q7 V12 TDI QUATTRO -

Brand: Audi Pages: 20

Brand: HawksHead Pages: 10

Brand: PAC Pages: 4

Brand: Van Guard Pages: 12

ESPAS10 MONEYBOX

Brand: BFT Pages: 26

Brand: Edelbrock Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands