Factory Five Racing Type 65 Coupe Assembly Manual Download Page 389 | Manualshive

Page: 389 / 442

background image

388

www.factoryfive.com

508-291-3443

Wheels and Tires



If using a wheel wider than 7”, FFR front lower control arms are needed to prevent the wheels
rubbing the control arms.

The front of the car can accommodate up to a 10” wheel with 315/35R-17. The rear of the car can
accommodate up to a 12” wheel with 335/35R-17

If you are using bolt-on aluminum Halibrand style wheel, we recommend using B.F. Goodrich

®

Radial

T/A’s, but in different sizes. The dimensions are the same 235/60/R15’s up front, but bigger
275/50/R15’s in the rear.

Tire

Rim

Acceptable range

235/60 15

6.5 – 8.5

245/45 17

8

7.5 – 9

275/50 15

7.5 – 10

275/40 17

9

9 – 11

315/35 17

10

10 – 12

335/35 17

11

11 – 13

Information from Pirelli.com, yokohamatire.com and bfgoodrich.com

The max rim width for a 3-link is a 10.50”
If you have any questions please call the Tech department at 508-291-3443.

Wheel specifications:

Best

Acceptable range

Front:

8” rim

5” Backspace

9” rim

5” Backspace

5”-6”

10” rim

6” Backspace

Rear:

9” rim

6” Backspace

4”- 6”

10” rim

6” Backspace

4”- 6”

11” rim

6” Backspace

5”- 6”

12” rim

6” Backspace

«
...
387
388
389
390
391
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: Laser Pages: 8

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: FormFit Pages: 4

Brand: Kuda Pages: 3

TRI-FOLD PG9300RF

Brand: Pet Gear Pages: 4

Brand: MULTILIFT Pages: 62

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: AIS Pages: 2

FOLDING TOP 1971

Brand: Fisher Body Pages: 37

Brand: Manik Pages: 2

Brand: Anker Technology Pages: 8

Brand: TomTom Pages: 22

Brand: Master Tailgaters Pages: 10

Brand: Chevrolet Pages: 46

Brand: Quadratec Pages: 8

Brand: Laser Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands