Factory Five Racing Type 65 Coupe Assembly Manual Download Page 395 | Manualshive

Page: 395 / 442

background image

394

www.factoryfive.com

508-291-3443

High Horsepower Transmissions

Stock:  T-5
The stock T-5 is good for the stock 302 engine.  If the engine is going to have some work done to it then
an upgrade to a heavy duty, Ford Racing “Z” T-5 is all that is needed.  An additional change to a Tremec
TKO 500 or 600 is needed if the engine that will be used has 350lbft of torque or more.  One unique
feature of the Tremec TKO is it allows the shifter to be relocated 8” forward of the normal shifter
location if a vertical shifter is desired verses a forward angled shifter.

Steering Rack

Stock:  15:1
Once the car is rolling either a 15:1 or 18:1 rack will yield about the same effort feel.  This is good for
most driving situations.  We have found that many of the Challenge Car racers prefer to use power
steering.  This can be done by using the stock 1987-1993 15:1 Mustang power rack and power steering
pump.  If changing to a manual 18:1 rack, a universal joint with a different number of splines will be
necessary in order to connect the steering shaft to the steering rack.  Factory Five offers a 18:1 manual
rack and the correct splined adapter for it.

Spindles

87-93 – 4 lug, limited wheel selection, limited brake packages available
94-04 – 5 lug, many wheels and brakes available

FFR two piece spindles (FFR#14850) – 5 lug, many wheels and brakes plus improved suspension
geometry, improved steering feel and more adjustability over 94-04 spindles.

«
...
393
394
395
396
397
...
»

Summary of Contents for Type 65 Coupe



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Type 65 Coupe

Brand: ULTIMATE SPEED Pages: 19

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: Cadillac Pages: 518

Brand: Opel Pages: 141

Automotive 31006

Brand: KRAFTWERK Pages: 2

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Metra Electronics Pages: 8

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Cadillac Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands