EVS Synapse GED100 Manual Download Page 51

Page: 51 / 74

SDIS2020Stat

This item indicates the status of the SDI S2020 metadata input. Can be OK,
error or NA.

S2020-Src_Method

This status indicates the S2020 Mapping Method as present on the current
SDI S2020 source. Can be NA (not available), Method A or Method B.

S2020-Src_Ass_Ch

Shows the S2020 SDID association channel. Can be None, NA (not
available) or Ch01/02 ~ Ch15/16.

SDIS2020Prog

This status indicates the program config as present on the current SDI
S2020 source. Can be one of the following values:

•

5.1+2

•

3x2

•

5.1+1+1

•

6x1

•

4+4

•

2+2

•

4x2

•

7.1

•

8x1

•

Other

•

5.1

•

DecMetaStat

This item indicates the status of the decoder metadata output. Can be

error

DecMetaProg

Indicates the program config as present in the Dolby E decoder metadata
output. Refer to

SDIS2020Prog

above for the list of possible values.

LocMetaStat

This item indicates the status of the local metadata input (RJ45 backplane).
Can be

error

LocMetaProg

Indicates the program config as present in the local metadata input. Refer to

SDIS2020Prog

above for the list of possible values.

The source of the following status items (preceded with ‘MD’ prefix) is dependent on the MD_Status_Src
and MD_Status_pgm settings.

Setting

Description

MD Prgm Config

This status indicates the program config as present on the metadata preset
selected with MetaDet. Can be one of the values listed under

SDI1S2020Prog

MD FrameRate

Indicates the value of the frame rate metadata parameter.

MD ProgramText

Displays the program’s text field (set with #Program_txt).

MD AC3Datarate

Indicates the value of the AC3 bitrate metadata parameter.

MD Bitstream

Indicates the value of the bitstream mode metadata parameter.

MD ChannelMode

Indicates the value of the channel mode metadata parameter.

MD CenterMixLvl

Indicates the value of the Center downmix level metadata parameter.

MD SrndMixLvl

Indicates the value of the surround downmix level metadata parameter.

INSTALLATION AND OPERATION MANUAL

Synapse GED100 | 6. Status Menu |

Summary of Contents for Synapse GED100











































































Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands

EVS Synapse GED100, Manual

Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands