EVS Synapse GED100 Manual Download Page 52

Page: 52 / 74

MD D_Surnd

Indicates the value of the Dolby surround metadata parameter.

MD LFE

Indicates the value of the LFE channel metadata parameter.

MD Dialog Lvl

Indicates the value of the dialogue level metadata parameter.

MD LanguageCode

Indicates the value of the language code metadata parameter.

MD AudioProdInfo

Indicates the value of the audio production info metadata parameter.

MD ProdMixLvl

Indicates the value of the audio production mix level parameter.

MD ProdRoomType

Indicates the value of the audio production room type parameter.

MD AC3Copyright

Indicates the value of the AC3 copyright metadata parameter.

MD AC3OrigBitstr

Indicates the value of the AC3 original bitstream metadata parameter.

MD Pref. Dwnmx

Indicates the value of the preferred downmix metadata parameter.

MD Lt/RtCDwnmx

Indicates the value of the Lt/Rt center downmix metadata parameter.

MD Lt/RtSDwnmx

Indicates the value of the Lt/Rt surround downmix metadata parameter.

MD Lo/RoCDwnmx

Indicates the value of the Lo/Ro center downmix metadata parameter.

MD Lo/RoSDwnmx

Indicates the value of the Lo/Ro surround downmix metadata parameter.

MD D_Surnd Ex

Indicates the value of the Dolby surround EX metadata parameter.

MD D_HeadPhone

Indicates the value of the Dolby headphone metadata parameter.

MD ADConvType

Indicates the value of the A/D conversion type metadata parameter.

MD DC Filter

Indicates the value of the DC filter metadata parameter.

MD Lowpass Fil

Indicates the value of the Low pass filter metadata parameter.

MD LFE Filter

Indicates the value of the LFE filter metsdata parameter.

MD Sur PhShift

Indicates the value of the surround phase shift metadata.

MD Sur3dB Att

Indicates the value of the surround 3dB attenuate metadata.

MD RFPreEmph

Indicates the value of the RF pre emphasis metadata parameter.

MD RF Mode

Indicates the value of the RF mode metadata parameter.

MD Line Mode

Indicates the value of the line mode metadata parameter.

FPGA-Stat

Displays the status of the FPGA chip. Can be error or OK.

DM-D_Type

Displays which type of input or output board is currently detected on circuit
D. Can be CAT561 Dec, CAT561 Enc or CAT561 EPD. For the GED100, this
should always be the CAT561 EPD.

DM-D_Status

Indicates the status of I/O board A, can be

NAor Error

| November 2021 | Issue 1.00.B

Summary of Contents for Synapse GED100











































































Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands

EVS Synapse GED100, Manual

Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands