EVS Synapse GED100 Manual Download Page 33

Page: 33 / 74

#Emb-A1 ~ #Emb_A4 With this setting you decide which audio channel out of the above selected

source is used for embedder A channels 1 through 4. Can be any of the
available 16 channels or set to

off

#SourceEmb-B1 ~
#SourceEmb-B4

With these settings you can select where the corresponding audio channels
(channel B1 through channel B4) of embedder B are coming from:

SDI

: Audio comes from the SDI input

DecoderOut

: Audio comes from the Dolby E decoder (8 ch)

EncoderOut

: Audio comes from the Dolby encoder (8 ch)

AddOn01/16

: Audio comes from add-on bus (first 16 ch)

AddOn17/32

: Audio comes from add-on bus (second 16 ch).

#Emb-B1 ~ #Emb_B4 With this setting you decide which audio channel out of the above selected

source is used for embedder B channels 1 through 4. Can be any of the
available 16 channels or set to

off

#SourceEmb-C1 ~
#SourceEmb-C4

With these settings you can select where the corresponding audio channels
(channel C1 through channel C4) of embedder C are coming from:

SDI

: Audio comes from the SDI input

DecoderOut

: Audio comes from the Dolby E decoder (8 ch)

EncoderOut

: Audio comes from the Dolby encoder (8 ch)

AddOn01/16

: Audio comes from add-on bus (first 16 ch)

AddOn17/32

: Audio comes from add-on bus (second 16 ch) .

#Emb-C1 ~ #Emb_C4 With this setting you decide which audio channel out of the above selected

source is used for embedder C channels 1 through 4. Can be any of the
available 16 channels or set to

off

#SourceEmb-D1 ~
#SourceEmb-D4

With these settings you can select where the corresponding audio channels
(channel D1 through channel D4) of embedderD are coming from:

SDI

: Audio comes from the SDI input

DecoderOut

: Audio comes from the Dolby E decoder (8 ch)

EncoderOut

: Audio comes from the Dolby encoder (8 ch)

AddOn01/16

: Audio comes from add-on bus (first 16 ch)

AddOn17/32

: Audio comes from add-on bus (second 16 ch)

#Emb-D1 ~ #Emb_D4 With this setting you decide which audio channel out of the above selected

source is used for embedder D channels 1 through 4. Can be any of the
available 16 channels or set to

off

#EmbA1_Gain ~
#EmbD4_Gain

Adjusts the gain for the corresponding incoming audio input between -144 and
12dB. Everything below -144dB (indicated as -999 dB) means the audio will be
muted.

INSTALLATION AND OPERATION MANUAL

Synapse GED100 | 5. Settings Menu |

Summary of Contents for Synapse GED100











































































Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands

EVS Synapse GED100, Manual

Search results

Summary of Contents for Synapse GED100

Reviews:

Related manuals for Synapse GED100

Brands by name

Popular brands