Epson Stylus Pro 9000 Printer Manual Download Page 99

Page: 99 / 165

A-2

A-2

Installing an Interface Card

2. Use a Phillips-head (+) screwdriver to remove the two screws securing

the shield plate to the back of the printer. Then lift off the plate.

Be sure to keep the screws so you can use them if you re-install the shield
plate.

3. Make sure you set any jumpers or DIP switches on the card. See the

card’s documentation for details.

On the FireWire card, make sure DIP switch 10 is set to

(advanced

mode).

4. Slide the interface card along the slots on both sides of the

compartment. Push it in firmly to fully insert the connector into the
printer’s internal socket.

Summary of Contents for Stylus Pro 9000






































































































































































Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands

Epson Stylus Pro 9000, Printer Manual

Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands