Epson Stylus Pro 9000 Printer Manual Download Page 45 | Manualshive

Page: 45 / 165

background image

2-2

2-2

|

Monitoring and Configuring the Printer

Monitoring Normal Printer Operation

Messages appear on the control panel display and lights come on or flash to
indicate various phases of printer operation. The following table explains the
status messages and lights:

Pausing and Resetting the Printer

If you need to stop the printer during a print job, press the

Pause

button.

Press the

Pause

button again to resume printing.

If you decide to cancel a job after the printer has started processing it, you
can reset the printer. Press the

Pause

button and hold it down for 3 seconds.

This clears all data in the printer’s memory.

Checking Printer Status

You can use the control panel to print a status check or nozzle check. These
prints allow you to test the printer without sending a print job (and without
connecting the printer to the RIP). You can also check the amount of ink
remaining, total number of prints, and the status of your cutter blade and
other printer parts.

Status messages

Message

Light

Explanation or response

READY

Operate

light on

Printer is ready to print.

PRINTING

Operate

light flashing Printer is receiving data.

INK DRY
<number> MIN

Pause

light flashing

Printer is paused to let ink dry.
Wait for the number of minutes
shown.

RESET

All lights flash briefly

Printer is resetting.

PRESS PAUSE
BUTTON

Pause

light on

Press the

Pause

button to

continue.

WAIT

Pause

light on or

flashing

Printer is warming up, performing
maintenance, or charging ink.

PAUSE

Pause

light on

Printer is paused. To resume
printing, press the

Pause

button.

«
...
43
44
45
46
47
...
»

Summary of Contents for Stylus Pro 9000






































































































































































Reviews:

No comments

Related manuals for Stylus Pro 9000

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

Brand: YOUPAI Pages: 15

Brand: TallyGenicom Pages: 15

Brand: DASCO Pages: 2

Brand: Microplex Pages: 135

8437477 - EasyShare ESP 9 All-In-One Printer

Brand: Kodak Pages: 143

Brand: Citizen Pages: 3

Brand: Oce Pages: 366

Brand: Konica Minolta Pages: 28

Brand: Canon Pages: 2

Brand: Canon Pages: 4

Brand: Canon Pages: 2

PIXMA MG6220 Installing

Brand: Canon Pages: 4

PIXMA MG7500 Series

Brand: Canon Pages: 4

Brand: Canon Pages: 676

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands