manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual, Page: 2 / 317

Share
Download
Epson ActionPrinter 4500 User Manual Download Page 2

EPSON

®

Product Update Notice

This booklet describes the new features of your printer that have
been added since the User’s Manual was printed.

Print Speed

Your printer now prints at the following speeds.

Quality

Draft

Letter

Characters/inch

Characters/second/line

10

160

12

192

10

53

12

64

Loading Single Sheets of Paper

The printer now automatically loads single sheets of paper. Follow

these steps whenever you load a single sheet of paper:

1. Turn on the printer.

2.

Insert a sheet of paper in the paper guide until it meets
resistance. After about two seconds, the printer loads the paper
automatically and is set on line so that it can accept data from
your computer.

When loading a single sheet of paper, you do not press 

LOAD/EJECT

or 

ON LINE.

Product Update Notice

1

4000308
C01-00

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments