Epson ActionPrinter 4500 Page 81 User Manual Download

Page: 81 / 317

Operating the Control Panel

The indicator lights give you the current status of the printer. The
buttons and paper handling functions let you control many of the

printer settings.

Lights

MULTI-PART

(orange)

POWER

PAPER

On when the paper thickness
lever is set to position

higher. When this light is
blinking, the micro-adjustment

DRAFT

FORM

ROMAN

FEED

SANS SERIF

SLOT

LINE

FEED

LOAD

CONDENSED

function can be used.

POWER

(green)

On when the POWER switch is on
and power is supplied.

READY

(green)

On when the printer is ready to

accept input data. Flickers during
printing.

-PAPER OUT

(red)

On when the printer is out of
paper or when continuous paper
is in the standby position.

ON LINE

(green)

On when the printer is on line

and ready to accept data.

3-2

Using the Printer

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands

Epson ActionPrinter 4500, User Manual

Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands