Epson ActionPrinter 4500 Page 135 User Manual Download | Manualshive

Page: 135 / 317

background image

User-defined Characters

Copying ROM Characters to RAM

After running the program, if you select the user-defined character set
and try to print other characters, the only one that will print is your
arrow. Since no other characters are in the printer’s user-defined RAM,

there is nothing else to print. Other characters sent to the printer do not
even print as spaces; it’s as if they were not sent at all.

In many cases, you will want to redefine only a few of the characters to
suit your needs-the rest of the alphabet will work fine as it is. As you
have seen, it is possible to switch back and forth, at will, between the

normal character set and your user-defined character set. It is, however,
rather inconvenient.

Therefore, your printer has a command that allows you to copy all of

the standard characters from ROM to the user-defined character set.

The command format is as follows, where the value of n represents the

font family:

E S C : 0 n 0

Note:

This command cancels any user-defined characters you have

already created. You must send this command to the printer before
you define characters.

If you use this command at the beginning of a program, then define
your special characters and select the user-defined set, you can print
with the user-defined set as your normal character set. You never need

to switch back and forth between sets.

4-28

Software and Graphics

«
...
133
134
135
136
137
...
»

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Brand: Unimark Pages: 36

Brand: Oki Pages: 24

Brand: Oki Pages: 95

Brand: Oce Pages: 268

Brand: Axiohm Pages: 8

Brand: iDPRT Pages: 74

Brand: Memjet Pages: 181

Brand: E-Pos Pages: 21

THERMOMARK ROLLMASTER 300

Brand: Phoenix Contact Pages: 42

ApeosPort-IV C5580

Brand: Fuji Xerox Pages: 739

Brand: Ricoh Pages: 678

Brand: Daewoo Pages: 37

Brand: Oki Pages: 220

Brand: Loadrite Pages: 16

AcuLasaer C1900

Brand: Epson Pages: 17

3880 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 2

AcuLaser CX11NF

Brand: Epson Pages: 64

Brand: Epson Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands