Epson ActionPrinter 4500 Page 169 User Manual Download

Page: 169 / 317

The Pull Tractor

2. Press the

ON LINE

button to set the printer off line. Then, press the

LOAD/EJECT

button until the continuous paper feeds backward out

of the paper path to the standby position. The

PAPER OUT

light

comes on when the paper is completely out of the paper path.

3. Push the paper release lever all the way back for single sheet paper

(as shown) or to the middle position for continuous feed paper.

Using the Printer Options

5-31

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands

Epson ActionPrinter 4500, User Manual

Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands