manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

Share
Download
Epson ActionPrinter 4500 User Manual Download Page 44

Testing 

the 

Printer

If the Self Test Does Not Work

If 

the 

self test does not print properly, check 

the 

control panel and 

the

print head area. If paper is jammed, turn off 

the 

printer. Then remove

the paper using the platen knob and load a new sheet. Make sure that
all packing material and shipping restraints have been removed from
inside the printer. See 

the 

Removing the Protective Materials section in

this chapter for information on removing the locking clip. You can also
see Chapter 7 for further information.

Problem

Solution

The printer sounds like

it is printing, but

nothing is printed.

The test did not print

when you pressed the

ON 

LINE button.

The ribbon may not be installed properly.
Turn off the printer, reinstall the ribbon
cartridge, and then tighten the ribbon by
turning the ribbon-tightening knob. Make
sure the ribbon passes between the print head
and ribbon guide. See page 1-10.

The ribbon may be worn. Replace the ribbon
cartridge. See page 6-5.

Turn off the printer and repeat the self test.
Make sure you hold down the 

FORM FEED 

or

LINE FEED 

button the entire time you are

turning 

on the 

printer.

Turn off the printer and disconnect the cable
from the host computer. Try the self test
again.

If the printer still does not print the self test
correctly, contact the store where you
purchased your printer or call the Epson

toll-free number (1-800-922-8911).

1-22

Setting Up the Printer

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands