manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

The Epson ActionPrinter 4500 is a reliable and high-performance printer designed for efficient and professional printing needs. As a user-friendly device, it comes with a comprehensive User Manual, which can be easily downloaded for free from manualshive.com, providing step-by-step guidance for optimal usage and maintenance.

Share
Download
background image

Printing on Special Paper

To

1.

change the paper thickness setting, follow these steps.

Make sure that the printer is turned off. Then remove the
cover.

printer

WARNING: 

If the printer has just been in use, 

the 

print head

may be hot. Allow it to cool before touching it,

2. Select the paper thickness you want according to the table on the

following page. For normal use, the lever should always be set to
position 2 on the scale.

To help you check the position of the paper thickness lever, the
orange 

MULTI-PART 

light on the control panel comes on if the lever

is set to position 4 or higher.

Paper Handling

2-25

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Canon Color imageCLASS MF8580Cdw User Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon ImageCLASS 2300 Setup Sheet preview
ImageCLASS 2300
Brand: Canon Pages: 8
Canon Color imageCLASS MF8580Cdw Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 750
Canon Color imageCLASS 8180c Facsimile Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 95
Canon GP200 Installation Instructions preview
GP200
Brand: Canon Pages: 4
Canon CFX-B380 IF Parts List preview
CFX-B380 IF
Brand: Canon Pages: 49
Canon ImageCLASS 2300 Basic Manual preview
ImageCLASS 2300
Brand: Canon Pages: 156
Canon FaxPhone L90 Reference Manual preview
FaxPhone L90
Brand: Canon Pages: 193
QMS 3225 Tray Module Installation Manual preview
3225
Brand: QMS Pages: 24
Canon imageCLASS D1120 User Manual preview
imageCLASS D1120
Brand: Canon Pages: 36
Canon ImageCLASS 2300 Remote Ui Manual preview
ImageCLASS 2300
Brand: Canon Pages: 44
Canon FAXPHONE L75 Software User'S Manual preview
FAXPHONE L75
Brand: Canon Pages: 66
Samsung CLP-36 Series Manual preview
CLP-36 Series
Brand: Samsung Pages: 9
Samsung Bixolon SRP-500 Command Manual preview
Bixolon SRP-500
Brand: Samsung Pages: 27
Samsung 550N - CLP Color Laser Printer User Manual preview
550N - CLP Color Laser Printer
Brand: Samsung Pages: 288
Samsung 2 COLOR THERMAL PRINTER SRP-275 Quick Reference Manual preview
2 COLOR THERMAL PRINTER SRP-275
Brand: Samsung Pages: 8
Samsung CLP-300 Brochure & Specs preview
CLP-300
Brand: Samsung Pages: 6
Samsung CLP-300 User Manual preview
CLP-300
Brand: Samsung Pages: 91

Brands by name

Popular brands

Load more brands