manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

The Epson ActionPrinter 4500 is a reliable and high-performance printer designed for efficient and professional printing needs. As a user-friendly device, it comes with a comprehensive User Manual, which can be easily downloaded for free from manualshive.com, providing step-by-step guidance for optimal usage and maintenance.

Share
Download
background image

Power Supply

Problem

Solution

Power is not being
supplied.

The 

POWER 

light does

not go on.

The power cable may be loose or not
properly plugged into the electrical outlet.
Turn off the printer, see that the power

cable is properly plugged in to the electrical

outlet, and turn the printer back on.

The power switch is off. Turn on the

switch.

Power is not being supplied to the electrical
outlet. Plug another electrical device into
the outlet to determine whether the outlet

is operating properly. If the electrical outlet
is controlled by a switch, use an electrical

outlet that is not controlled by an outside
switch.

7-4

Troubleshooting

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

Canon image Prograf iPF785 Series Basic Manual preview
image Prograf iPF785 Series
Brand: Canon Pages: 136
GBC A1 Operation & Instruction Manual preview
A1
Brand: GBC Pages: 110
Xerox M Series Initial Setup Card preview
M Series
Brand: Xerox Pages: 2
Canon FaxPhone L120 Starter Manual preview
FaxPhone L120
Brand: Canon Pages: 11
Canon imageRUNNER ADVANCE 8085 Maintenance Manual preview
imageRUNNER ADVANCE 8085
Brand: Canon Pages: 176
Canon FaxPhone L120 Software Manual preview
FaxPhone L120
Brand: Canon Pages: 85
Canon imageRUNNER 5070 Specification preview
imageRUNNER 5070
Brand: Canon Pages: 4
Canon imageRUNNER 5570 Specification preview
imageRUNNER 5570
Brand: Canon Pages: 4
Canon IMAGERUNNER 7095 PRINTER Brochure & Specs preview
IMAGERUNNER 7095 PRINTER
Brand: Canon Pages: 8
Canon IMAGERUNNER 7105 Service Manual preview
IMAGERUNNER 7105
Brand: Canon Pages: 21
Canon FaxPhone L120 Advanced Manual preview
FaxPhone L120
Brand: Canon Pages: 58
Canon IMAGERUNNER ADVANCE C5051 Manual preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 12
Canon imageRUNNER ADVANCE C2020 Setup Manual preview
imageRUNNER ADVANCE C2020
Brand: Canon Pages: 68
Canon imageRUNNER ADVANCE 6055 Maintenance Manual preview
imageRUNNER ADVANCE 6055
Brand: Canon Pages: 134
Canon Color imageRUNNER LBP5970 Getting Started Manual preview
Color imageRUNNER LBP5970
Brand: Canon Pages: 67
Canon FAXPHONE L170 - B/W Laser - Copier Starter Manual preview
FAXPHONE L170 - B/W Laser - Copier
Brand: Canon Pages: 12
Canon FAXPHONE L100 Technical Information preview
FAXPHONE L100
Brand: Canon Pages: 2
Canon imageRunner 1133 Starter Manual preview
imageRunner 1133
Brand: Canon Pages: 60

Brands by name

Popular brands

Load more brands