Epson ActionPrinter 4500 Page 208 User Manual Download

Page: 208 / 317

Printing

Problem

Solution

The printer does not

print (continued).

The printer sounds like

it is printing, but
nothing is printed.

The printer makes a

strange noise, the

beeper sounds several
times, and the printer
stops abruptly.

The ON LINE light is

flickering but the
printer does not print,

or it stops printing
abruptly.

The print is faint or

uneven.

Printed characters

have parts missing at
the bottom as shown

here.

A B C D

The ribbon cartridge may not be installed
properly. Turn off the printer, reinstall the

ribbon cartridge, and take up any slack in
the ribbon.

The ribbon may be worn. Replace the

ribbon cartridge. See Chapter 6.

This indicates an error in printer operation.
Turn off the printer, check for paper jams

or other problems; then turn the printer

back on. If the printer still does not print

correctly, contact the store where you
purchased your printer or call the Epson

toll-free number (1-800-922-8911).

The print head is overheated. Wait a few
minutes; the printer resumes printing

automatically when

the

print head cools.

The ribbon cartridge may not be installed
properly. Remove the ribbon cartridge and

reinstall it. Make sure the cartridge hooks
are inserted securely into the printer. See

Chapter 1.

7-6

Troubleshooting

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands

Epson ActionPrinter 4500, User Manual

Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands