manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

Share
Download
Epson ActionPrinter 4500 User Manual Download Page 179

The Interface Boards

Compatible Interfaces

The following is a list of Epson interfaces that are compatible with your
printer.

Interface number

Name

#8143

New Serial Interface

#8148

Intelligent serial interface

#8165

Intelligent IEEE-488 interface

#8172

32 KB buffered parallel interface

All Epson interfaces have the Epson name printed on them. If the board
has an identification code printed on it, it is a four-digit number
beginning with 8 and should correspond to one of the numbers listed in

the table above.

Also, Coax and Twinax interfaces are available from third party
vendors. These interfaces allow connectivity to mainframes and

minicomputers and emulation of IBM printers. The Coax (EP-Connect)
is available from Avatar Corporation (508) 435-6872, and the Twinax

(I-O8300) is available from I-O Corporation (801) 973-6767.

Installation

1. Turn off your printer. Then unplug the printer and disconnect the

interface cable.

Using the Printer Options

5-41

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands