Epson ActionPrinter 4500 Page 246 User Manual Download

Page: 246 / 317

Interface Specifications

The column heading “Direction” refers to the direction of signal
flow as viewed from the printer.

“Return” denotes the twisted-pair return, to be connected at signal

ground level. For the interface wiring, be sure to use a twisted-pair

cable for each signal and to complete the connection on the return
side. These cables should be shielded and connected to the chassis

of the host computer and the printer.

All interface conditions are based on TTL level. Both the rise and
the fall times of each signal must be less than

0.2

microseconds.

Data transfer must be carried out by observing the ACKNLG or

BUSY signal. Data transfer to this printer can be carried out only
after receipt of the ACKNLG signal or when the level of the BUSY
signal is LOW.

Interface Timing

The figure below shows the timing for the parallel interface.

0.5 Min.

8-10

Technical Specifications

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands

Epson ActionPrinter 4500, User Manual

Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands