Epson ActionPrinter 4500 Page 209 User Manual Download

Page: 209 / 317

Printing

Problem

The print is faint or

uneven (continued).

The printout is faint.

Solution

The ribbon may be worn out. A worn
ribbon can damage the print head and
should be replaced. Install a new ribbon
cartridge. See Chapter 6.

Dots are missing in the

printed characters or

graphics.

A line of dots is

missing in the
printout.

Dots are missing in

random positions.

The paper thickness lever may not be set

correctly for the paper you are using. Set
the paper thickness lever to match the
thickness of your paper. See Chapter 2.

The print head is damaged. Stop printing
and call the Epson toll-free number

(1-800-922-8911) for information on where
to have the printer repaired.

There is either too much slack in the ribbon
or the ribbon has come loose and gotten

caught on something. Stop printing, turn
off the printer, and reinstall the ribbon

cartridge. See Chapter

Troubleshooting

7-7

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands

Epson ActionPrinter 4500, User Manual

Search results

Summary of Contents for ActionPrinter 4500

Reviews:

Related manuals for ActionPrinter 4500

Brands by name

Popular brands