manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual

The Epson ActionPrinter 4500 is a reliable and high-performance printer designed for efficient and professional printing needs. As a user-friendly device, it comes with a comprehensive User Manual, which can be easily downloaded for free from manualshive.com, providing step-by-step guidance for optimal usage and maintenance.

Share
Download
background image

The Pull Tractor

Although the pull tractor can be used in combination with the built-in
push tractor as described above, the pull tractor can also be used by

itself. Instead of setting the paper on the pins of the push tractor,
simply insert it through the same paper path as you would use with
single-sheet paper.

CAUTION: 

Do not use the short tear-off feature with the pull

tractor. Before you start printing with the pull tractor, be sure
the DIP switch 

2-2 

is set to off.

Removing the Pull Tractor

1. Make sure to tear off the printed document and remove the tractor

cover and paper guide. Then turn on the printer.

5-30

Using the Printer Options

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments

Related manuals for ActionPrinter 4500

MAKERGEAR Ultra One User Manual preview
Ultra One
Brand: MAKERGEAR Pages: 8
Oki C831 Material Safety Data Sheet preview
C831
Brand: Oki Pages: 8
Oki C831 Safety And Warranty Manual preview
C831
Brand: Oki Pages: 48
X-Rite Stylus Pro 7900 Setup And Maintenance Manual preview
Stylus Pro 7900
Brand: X-Rite Pages: 36
Fenix Imvico TK41 Operation Manual preview
TK41
Brand: Fenix Imvico Pages: 88
Xerox PHASER 6140 Quick Manual preview
PHASER 6140
Brand: Xerox Pages: 4
Datamax MP-Compact4 Programmer'S Reference Manual preview
MP-Compact4
Brand: Datamax Pages: 95
Datamax Mark II E-4205e Operator'S Manual preview
Mark II E-4205e
Brand: Datamax Pages: 72
BCS 4206 Operating Manual preview
4206
Brand: BCS Pages: 151
Zonestar Z8PM4 Pro User Manual preview
Z8PM4 Pro
Brand: Zonestar Pages: 25
ABLE Ap1400 Programmer'S Manual preview
Ap1400
Brand: ABLE Pages: 42
Xerox B305 Quick Reference Manual preview
B305
Brand: Xerox Pages: 20
U-Line ZEBRA ZD410 Manual preview
ZEBRA ZD410
Brand: U-Line Pages: 18
Konica Minolta PC-410 Installation Manual preview
PC-410
Brand: Konica Minolta Pages: 8
Kyocera Mita Ecosys FS-1800+ Installation Manual preview
Ecosys FS-1800+
Brand: Kyocera Mita Pages: 31
Xerox CopyCentre 118 Installation Manual preview
CopyCentre 118
Brand: Xerox Pages: 2
Galileo ADP 3000 Quick Reference preview
ADP 3000
Brand: Galileo Pages: 15
Lexmark C925 User Manual preview
C925
Brand: Lexmark Pages: 221

Brands by name

Popular brands

Load more brands