manualshive.com logo in svg

Epson ActionPrinter 4500, User Manual, Page: 23 / 317

Share
Download
Epson ActionPrinter 4500 User Manual Download Page 23

Chapter 1

Setting Up the Printer

Unpacking the Printer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Checking the Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Removing the Protective Materials . . . . . . . . . . . . . . . . . . . . 1-3

Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Assembling the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Installing the Platen Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Installing the Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . .

1-8

Attaching the Paper Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Testing the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-14

Plugging in the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Running the Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-15

If the Self Test Does Not Work . . . . . . . . . . . . . . . . . . . . . . .

1-22

Connecting the Printer to Your Computer . . . . . . . . . . . . . . . .

1-23

The Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-23

Setting Up Your Application Software . . . . . . . . . . . . . . . . . . .

1-26

Choosing From a Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-26

Setting Up the Printer

1-1

Summary of Contents for ActionPrinter 4500






























































































































































































































































































































Reviews:

No comments