Endress+Hauser Liquisys M CLM 223 Operating Instructions Manual Download Page 65

Page: 65 / 83

8.4.2

Dismantling of CLM 223

• Consider potential effects on process

when removing the instrument from service!

• First pull off the terminal block (item 420 b)

on the rear of the instrument to de-energize
the instrument.

• Then pull off the terminal blocks (items 420

a and 430 if applicable) on the rear. Now
you can dismantle the instrument.

• Push the end frame latches (item 340)

inward and pull off the frame towards the
rear.

• Loosen the special screw (item 400) by

turning it counterclockwise.

• Remove the complete electronics block

from the housing. The modules are
plugged together mechanically and can be
easily separated:

–

Simply pull the processor/display module
off towards the front

–

Pull the back plate tabs outward slightly
to remove the lateral modules.

8.4.3

Assembly of CLM 223

• Reverse the dismantling sequence for

assembly.

• Hand-tighten the special screw without

using a tool.

• Incorrect assembly is not possible!

A module block which has been plugged
together incorrectly cannot be inserted in
the housing.

8.4.4

Spare parts for CLM 223

Item

Designation

Name

Function

Order number

Power supply unit

LSGA

100/115/230 V AC

51500317

Power supply unit

LSGD

24 V AC + DC

51500318

290

Relay module

LSR1-2

2 relays

51500320

300

Relay module

LSR1-4

4 relays

51500321

Conductive central module

LSCH-S1

1 current output

51501210

Conductive central module

LSCH-S2

2 current outputs

51501212

Conductive central module

LSCH-H1

1 current HART

51501213

Conductive central module

LSCH-H2

2 current o HART

51501214

Conductive central module

LSCP

Profibus PA / no current outp.!

51501215

Inductive central module

LSCH-S1

1 current output

51501216

Inductive central module

LSCH-S2

2 current outputs

51501218

Inductive central module

LSCH-H1

1 current HART

51501219

Inductive central module

LSCH-H2

2 current o HART

51501220

Inductive central module

LSCP

Profibus PA / no current outp.!

51501221

240

Conductivity transmitter

MKIC

Cond. + temp. input

51501206

330, 340

Housing assembly

With front membrane, key

tappets, gasket, special

screw, tensioning brackets,

all nameplates

51501075

310, 320,
340, 400

Mechanical housing parts

Back plate, side wall, end

frame, special screw

51501076

420a, 420b

Terminal strip set

Terminal strips for inputs /

outputs and for supply / alarm

relay

51501203

430

Terminal strip

Terminal strip for relay module

51501078

345

Ground terminal strip

PE and screen connections

51501086

LM253E08.CHP

Liquisys M CLM 223 / 253

Diagnosis and corrective maintenance

Hauser

Summary of Contents for Liquisys M CLM 223




















































































Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands

Endress+Hauser Liquisys M CLM 223, Operating Instructions Manual

Search results

Summary of Contents for Liquisys M CLM 223

Reviews:

Related manuals for Liquisys M CLM 223

Brands by name

Popular brands